Risco-group 2-Way RWX73M User Manual download pdf

RTTE Compliance Statement

Hereby, RISCO Group declares that this equipment is in

compliance with the essential requirements and other

relevant provisions of Directive 1999/5/EC. For the CE

Declaration of Conformity please refer to our website:

www.riscogroup.com

MAIN FEATURES

The RWX73M is a 2-way supervised transmitter that

combines Magnetic/Door contact against opening doors

and windows with additional universal input.

The RWX73M operates with RISCO Group 2-Way

wireless systems

NORMALLY CLOSED

INPUT CONFIGURATION

NORMALLY OPEN INPUT

CONFIGURATION

Step 2: Input Wiring

Use the following diagrams for appropriate input

termination wiring. For DEOL termination connect

two 10K Ohm resistors (supplied) illustrated as follows:

ALARM

DETECTOR

ALARM

DETECTOR

INSTALLATION

● Communication: Bi-directional

● Range: up to 300 m (1,000 ft.) range line of sight

● Supervision: Up to 255 minutes

● Selective input termination : NO, NC, DEOL

● Selective input response: 10 / 500ms

● Tamper protection: Back + Cover

Step 1: Transmitter Receiver Communication Set Up

The RWX73M must identify itself to the system's receiver

by writing its coded message into the receiver's address

memory.

This registration is performed either by entering the

RWX73M’s 11-digit serial code number or by performing

the following RF allocation steps:

1. Remove the front cover (Fig 1)

2. Set the main unit to Learn Mode.

3. Remove the battery from the insulation material and

reinsert it into the transmitter, paying attention to the

polarity (Fig. 4).

4. Send a write message by pressing both tamper

switches (back and cover) for at least 3 seconds

until panel recognition is displayed.

DOUBLE END OF LINE INPUT CONFIGURATION

10k

ALARM

TAMPER

10k

DETECTOR

Step 3: Select The Mounting Location

1. Select a location best suited for communication quality

and near the intended wired detector. RISCO recom-

mends you place the unit at the highest possible position.

2. Temporarily attach the unit to this point using two sided

adhesive tape

3. Generate an Alarm signal (by momentarily opening or

closing the input terminals) and verify that the receiver

has received the signal. If the alarm signal is not

detected, reposition the transmitter and try again.

Step 4: Final Mounting (Figures 1,2 and 3)

1. Separate the back part of the transmitter and mount all

the parts in place (Fig. 2 and 3), including the middle

back tamper mounting screw (T).

2. Mount the magnet (Fig. 5).

Notes:

1. The mark on the magnet's plastic case should be

aligned with the mark on the transmitter's case (Fig. 6).

2. For installations on wood or alloy, the maximum

distance for normal operation is 10mm, while for metal

ferromagnetic materials (iron) it is 5mm.

SW1

LED

BATTERY

ANTENNA

+ -

C RISCO

IN1

T.B

Step 5: Parameters

The following parameters can be deﬁned for RWX73M:

Parameter Option

Supervision Yes/No

LED Enable Yes/No

Magnet Enable/Disable

Alarm Hold On/Off

Termination IN1: NO/NC/DEOL

Response 10ms/500ms

TECHNICAL SPECIFICATIONS

ELECTRICAL

Battery Type: CR123 3V Lithium Battery

Current Consumption: 11µA standby

Frequency: RWX73M86800A 868.65 MHz

RWX73M43300A 433.92 MHz

Dead Time (HOLD ON): 2.5 minutes

Supervision Transmission: 0-255 minutes

Modulation Type: ASK

Battery Life: 3 years typical

Contact Size: 32 x 35 x 72 mm (1.3 x 1.4 x 2.8 in.)

Magnet Size: 16 x 11 x 72 mm (0.6 x 0.44 x 2.8 in.)

ENVIRONMENTAL

RF immunity: According to EN50130-4

Operating temperature: 0°C to 40°C (32°F to 104°F)

Storage temperature: -20°C to 60°C (-4°F to 140°F)

Speciﬁcations are subject to change without prior notice.

Should any questions arise please contact your supplier.

LED INDICATION

● Upon successful learning: short ﬂash sequence

● Normal operation: brief light upon transmission

● Low battery: short ﬂash sequence during transmission

EN 50131-2-6 Grade 2 Environmental Class II

2-Way Wireless

Magnetic/Door Contact

(Model RWX73M)

Operating Mode

The RWX73M reports events from IN1 and from the magnetic reed switch. In normal operation mode alarm is sent when the

input or magnet are triggered. When restored, it transmits a restoral message

RISCO Group Limited Warranty

RISCO Group and its subsidiaries and afﬁliates ("Seller") warrants its

products to be free from defects in materials and workmanship under

normal use for 24 months from the date of production. Because Seller

does not install or connect the product and because the product may

be used in conjunction with products not manufactured by the Seller,

Seller cannot guarantee the performance of the security system

which uses this product. Seller's obligation and liability under this

warranty is expressly limited to repairing and replacing, at Seller's

option, within a reasonable time after the date of delivery, any product

not meeting the speciﬁcations. Seller makes no other warranty,

expressed or implied, and makes no warranty of merchantability or of

ﬁtness for any particular purpose. In no case shall seller be liable for

any consequential or incidental damages for breach of this or any

other warranty, expressed or implied, or upon any other basis of

liability whatsoever.

Seller's obligation under this warranty shall not include any transporta-

tion charges or costs of installation or any liability for direct, indirect,

or consequential damages or delay. Seller does not represent that its

product may not be compromised or circumvented; that the product

will prevent any personal injury or property loss by burglary, robbery,

ﬁre or otherwise; or that the product will in all

cases provide adequate

warning or protection.

Seller, in no event shall be liable for any direct or indirect damages or

any other losses occurred due to any type of tampering, whether

intentional or unintentional such as masking, painting or spraying on

the lenses, mirrors or any other part of the detector.

Buyer understands that a properly installed and maintained alarm

may only reduce the risk of burglary, robbery or ﬁre without warning,

but is not insurance or a guaranty that such event will not occur or that

there will be no personal injury or property loss as a result thereof.

Consequently seller shall have no liability for any personal injury,

property damage or loss based on a claim that the product fails to

give warning. However, if seller is held liable, whether directly or

indirectly, for any loss or damage arising under this limited warranty

or otherwise, regardless of cause or origin, seller's maximum liability

shall not exceed the purchase price of the product, which shall be

complete and exclusive remedy against seller.

No employee or representative of Seller is authorized to change this

warranty in any way or grant any other warranty.

WARNING: This product should be tested at least once a week.

CAUTION: risk of explosion if battery is replaced by an incorrect type.

Dispose of used batteriess according to local regulations.

Hahoma 14, Rishon Lezion, ISRAEL

Contacting RISCO Group

Tel: +44-(0)-161-655-5500

E-mail: support-uk@riscogroup.com

ITALY

Tel: +39-02-66590054

E-mail: support-it@riscogroup.com

SPAIN

Tel: +34-91-490-2133

E-mail: support-es@riscogroup.com

FRANCE

Tel: +33-164-73-28-50

E-mail: support-fr@riscogroup.com

BELGIUM

Tel: +32-2522-7622

E-mail: support-be@riscogroup.com

U.S.A

Tel: +1-631-719-4400

E-mail: support-usa@riscogroup.com

BRAZIL

Tel: +55-11-3661-8767

E-mail: support-br@riscogroup.com

CHINA

(Hu) Tel: +86-21-52390066

E-mail: support-cn@riscogroup.com

CHINA

(SZ) Tel: +86-755-82789285

E-mail: support-cn@riscogroup.com

POLAND

Tel: +48-22-500-28-40

E-mail: support-pl@riscogroup.com

ISRAEL

Tel: +972-3-963-7777

E-mail: support@riscogroup.com

GENERAL DESCRIPTION

English

Fig. 3

Fig. 2

Fig. 6

Max.

1cm

Fig. 4

Fig. 5

Fig. 1

Back bracket

AUSTRALIA

Tel: +1800-991-542

E-mail: support-au@riscogroup.com

1 2

C RISCO 1
(SZ) Tel: +86-755-82789285 2

Summary of Contents

Page 1 - C RISCO

RTTE Compliance StatementHereby, RISCO Group declares that this equipment is in compliance with the essential requirements and other relevant provisio

Page 2 - (SZ) Tel: +86-755-82789285

Comments to this Manuals

No comments

Risco-group 2-Way RWX73M User Manual

Browse online or download User Manual for Safety Risco-group 2-Way RWX73M. RISCO Group 2-Way RWX73M Manuel d'utilisation

Summary of Contents

Comments to this Manuals

Related products and manuals for Safety Risco-group 2-Way RWX73M